|
|
|
MALE-MALE STANDOFFS:
STANDARD SIZES
See Technical / Engineering Data
DIAMETER: 1/8" / 5/32" / 3/16" / 1/4" / 5/16" / 3/8" / 1/2"
SHAPE: Round, Square and Hex
MATERIAL: Brass, Aluminum, 303 Stainless Steel, 316 Stainless Steel, Titanium, Carbon Steel, Natural Nylon, Black Nylon & Delrin®
BODY LENGTH: Wide variety of lengths- 1/64" (.015) increments- up to 6"
EXTERNAL THREAD LENGTH: Ranging from .125 through .625 depending on the thread size. Thread Locking Products available.
FINISH: Available in: Anodize (Sulphuric) Dichromate Seal, Yellow-Green / Anodize (Sulphuric) Hot Water Seal, Clear / Anodize (Chromic) Hot Water Seal, Dark Gray / Anodize -Black / Anodize-Black High Lustre / Cadmium Plate, Clear Chromate / Cadmium Plate, Commercial / Cadmium Plate, Gold Chromate / Nickel Plate / Chromium Plate (Bright) / Chromium Plate, Engineering / Chromium Plate Over Nickel Plate / Passivate / Bright Dip / Iridite-Clear / Iridite-Gold #14 / Alodine 1200 / Black Oxide-Brass / Black Oxide- Stainless Steel / Hot Tin Dip / Silver Plate / Electro Tin / Electro Tin 60/40 Solder / Zinc Plate .0002 Thick-Clear Chromate / Zinc Plate .0002 Thick, Yellow-Green Chromate / Zinc Plate .0002 Thick, Black Chromate / Alkali Caustic Etch.
THREAD: 2-56 through 1/4- 28 / External- Class UNC 2A / Thread Locking Products available. Mix & Match Different Threads & Lengths For Each Part.
TOLERANCE for Brass, Aluminum, Stainless Steel and Carbon Steel: Body Length: Up to 6" ± .005 / Over 6" ± .010 / External Thread Length Tolerance is ± .005. External Thread Length Tolerance is ± .005.
TOLERANCE for Nylon and Delrin®: Body Length: For all lengths the Tolerance is ± .010 / External Thread Length Tolerance is ± .010.
Diameter: Standard commercial bar stock tolerances.
No Undercut on Nylon or Delrin®.
MALE-MALE STANDOFFS:
METRIC SIZES
See Technical / Engineering Data
DIAMETER: 3mm / 4mm / 4.5mm / 5mm / 6mm / 8mm / 10mm / 13mm
SHAPE: Round, Square and Hex
MATERIAL: Brass, Aluminum, Stainless Steel, Carbon Steel, Nylon & Delrin®
BODY LENGTH: Wide variety of lengths- .5mm increments- up to 100mm
EXTERNAL THREAD LENGTH: Ranging from 3mm through 13mm depending on the thread size. Thread Locking Products available.
FINISH: Available in: Anodize (Sulphuric) Dichromate Seal, Yellow-Green / Anodize (Sulphuric) Hot Water Seal, Clear / Anodize (Chromic) Hot Water Seal, Dark Gray / Anodize -Black / Anodize-Black High Lustre / Cadmium Plate, Clear Chromate / Cadmium Plate, Commercial / Cadmium Plate, Gold Chromate / Nickel Plate / Chromium Plate (Bright) / Chromium Plate, Engineering / Chromium Plate Over Nickel Plate / Passivate / Bright Dip / Iridite-Clear / Iridite-Gold #14 / Alodine 1200 / Black Oxide-Brass / Black Oxide- Stainless Steel / Hot Tin Dip / Silver Plate / Electro Tin / Electro Tin 60/40 Solder / Zinc Plate .0002 Thick-Clear Chromate / Zinc Plate .0002 Thick, Yellow-Green Chromate / Zinc Plate .0002 Thick, Black Chromate / Alkali Caustic Etch.
THREAD: M2 through M8 / External- Class 6G / Thread Locking Products available.
Mix & Match Different Threads & Lengths For Each Part.
TOLERANCE for Brass, Aluminum, Stainless Steel and Carbon Steel: Body Length: Up to 100mm ± .15mm / Over 100mm to 150mm ± .20mm / Over 150mm
± .25mm / External Thread Length Tolerance is ± .15.
TOLERANCE for Nylon and Delrin®: Body Length: For all lengths the Tolerance is ± .25 / External Thread Length Tolerance is ± .20.
Diameter: Standard commercial bar stock tolerances.
No Undercut on Nylon or Delrin®
CAPTIVE PANEL HARDWARE:
STANDARD SIZES
See Technical / Engineering Data
DIAMETER: .132 through .750
SHAPE: Round and Hex. Hex head cannot be knurled. Hex head only available for 4000 and 4100 series.
MATERIAL: Stainless Steel, Carbon Steel, Aluminum, Brass (Also available in Nylon For Retainer Washers Only).
KNURL: Straight
HEAD: Knurled and Slotted
CONFIGURATION: Round Head Screws: Knurled / Slotted- Knurled / Unslotted. Hex Head Screws: Slotted & Unslotted.
LENGTH: Wide variety of lengths in 1/16" (.061) up to 2"
LENGTH (for retainers): Wide variety of lengths in 1/4" through 5/8"
RETAINER: Standard and Spring Loaded, .050 through .290 shank length
FINISH: Available in: Anodize (Sulphuric) Dichromate Seal, Yellow-Green / Anodize (Sulphuric) Hot Water Seal, Clear / Anodize (Chromic) Hot Water Seal, Dark Gray / Anodize -Black / Anodize-Black High Lustre / Cadmium Plate, Clear Chromate / Cadmium Plate, Commercial / Cadmium Plate, Gold Chromate / Nickel Plate / Chromium Plate (Bright) / Chromium Plate, Engineering / Chromium Plate Over Nickel Plate / Passivate / Bright Dip / Iridite-Clear / Iridite-Gold #14 / Alodine 1200 / Black Oxide-Brass / Black Oxide- Stainless Steel / Zinc Plate .0002 Thick-Clear Chromate / Zinc Plate .0002 Thick, Yellow-Green Chromate / Zinc Plate .0002 Thick, Black Chromate / Alkali Caustic Etch.
THREAD: 2-56 through 5/16-24 / Internal Thread- Class UNC 2B / External Thread- Class.
UNC 2A / Thread Locking Products available.
TOLERANCE: See chart on each part number page.
Diameter: Standard commercial bar stock tolerances.
CAPTIVE PANEL HARDWARE:
METRIC SIZES
See Technical / Engineering Data
DIAMETER: 5mm through 19mm
SHAPE: Round and Hex. Hex head cannot be knurled. Hex head only available for M4000 and M4100 series.
MATERIAL: Stainless Steel, Carbon Steel, Aluminum, Brass (Also available in Nylon For Retainer Washers Only).
KNURL: Straight
HEAD: Knurled and Slotted
CONFIGURATION: Round Head Screws: Knurled / Slotted- Knurled /Unslotted. Hex Head Screws: Slotted & Unslotted.
LENGTH: Wide variety of lengths in .5mm increments- up to 51mm.
LENGTH (for retainers): Wide variety of lengths in 6.5mm through 16mm.
RETAINER: Standard and Spring Loaded, 1.3mm through 16mm shank length.
FINISH: Available in: Anodize (Sulphuric) Dichromate Seal, Yellow-Green / Anodize (Sulphuric) Hot Water Seal, Clear / Anodize (Chromic) Hot Water Seal, Dark Gray / Anodize -Black / Anodize-Black High Lustre / Cadmium Plate, Clear Chromate / Cadmium Plate, Commercial / Cadmium Plate, Gold Chromate / Nickel Plate / Chromium Plate (Bright) / Chromium Plate, Engineering / Chromium Plate Over Nickel Plate / Passivate / Bright Dip / Iridite-Clear / Iridite-Gold #14 / Alodine 1200 / Black Oxide-Brass / Black Oxide- Stainless Steel / Zinc Plate .0002 Thick-Clear Chromate / Zinc Plate .0002 Thick, Yellow-Green Chromate / Zinc Plate .0002 Thick, Black Chromate / Alkali Caustic Etch.
THREAD: M2.5 through M8 / Internal Thread- Class 6H / External Thread- Class 6G / Thread Locking Products available.
TOLERANCE:See chart on each part number page.
Diameter: Standard commercial bar stock tolerances.
INSULATING WASHERS:
STANDARD SIZES
See Technical / Engineering Data
DIAMETER: 1/8" through 1"
SHAPE: Round
MATERIAL: Nylon, Teflon®, Lexan®, Ultem®, Delrin®, Phenolic
LENGTH: For Head Thickness: wide variety of lengths in 1/64" (.015) through .120.
FLAT WASHER THICKNESS: .016 through .156
INSIDE HOLE DIAMETER: Ranging from .055 through .377 for screw sizes 0-80 through 3/8-24. Reamed to +
.010/ - .000, conforming to screw tolerances.
SHANK LENGTH: Wide variety of lengths .015 through .490.
SHANK DIAMETER: Machined to +
.000 / - .005 assuring precision fit to mating hole.
EDGE: Chamfered to permit smooth entry.
FINISH: Colored material available upon request.
TOLERANCE: Inside hole diameter +
.010 / - .000 - All other tolerances ± .005.
Diameter: Standard commercial bar stock tolerances.
Shoulder Washers, Flat Washers- Precision Machined, Not Molded.
INSULATING WASHERS:
METRIC SIZES
See Technical / Engineering Data
DIAMETER: 3mm through 25mm
SHAPE: Round
MATERIAL: Nylon, Teflon®, Lexan®, Ultem®, Delrin®, Phenolic
LENGTH: For Head Thickness: wide variety of lengths in 0.4mm through 1.6mm.
FLAT WASHER THICKNESS: 0.4mm through 2.4mm
INSIDE HOLE DIAMETER: Ranging from 0.74 through .413 for screw sizes M1.6 through M10. Reamed to + .16 / - 0.0, conforming to screw tolerances.
SHANK LENGTH: Wide variety of lengths 1mm through 13mm
SHANK DIAMETER: Machined to +
0.0 / - 0.16 assuring precision fit to mating hole.
EDGE: Chamfered to permit smooth entry
FINISH: Colored material available upon request
TOLERANCE: Inside hole diameter +
0.17 / - 0.00 - All other tolerances see All Technical Data.
Diameter: Standard commercial bar stock tolerances.
Shoulder Washers, Flat Washers- Precision Machined, Not Molded.
THUMB SCREWS:
STANDARD SIZES
See Technical / Engineering Data
DIAMETER: 5/32" / 3/16" / 1/4" / 3/8" / 7/16" / 1/2"
SHAPE: Round
KNURL: Diamond (for easy grip)
MATERIAL: Brass, Aluminum, Stainless Steel, Carbon Steel
LENGTH: Wide variety of lengths in 3/16" up to 2.500".
FINISH: Available in: Anodize (Sulphuric) Dichromate Seal, Yellow-Green / Anodize (Sulphuric) Hot Water Seal, Clear / Anodize (Chromic) Hot Water Seal, Dark Gray / Anodize -Black / Cadmium Plate, Clear Chromate / Cadmium Plate, Commercial / Cadmium Plate, Gold Chromate / Nickel Plate / Chromium Plate (Bright) / Chromium Plate, Engineering / Chromium Plate Over Nickel Plate / Passivate / Iridite-Clear / Iridite-Gold #14 / Alodine 1200 / Black Oxide-Brass / Black Oxide- Stainless Steel / Zinc Plate .0002 Thick-Clear Chromate / Zinc Plate .0002 Thick, Yellow-Green Chromate.
THREAD: 2 -56 through 1/4-28 / External Thread- Class UNC 2A / Thread Locking Products available.
Available with slotted heads upon request
TOLERANCE: See chart on each part number page.
Diameter: Standard commercial bar stock tolerances.
THUMB SCREWS:
METRIC SIZES
See Technical / Engineering Data
DIAMETER: 4mm / 4.5mm / 5mm / 6mm / 6.5mm / 8mm / 10mm / 11mm / 13mm
SHAPE: Round
MATERIAL: Brass, Aluminum, Stainless Steel, Carbon Steel
KNURL: Diamond (for easy grip)
LENGTH: Wide variety of lengths in 8mm up to 58mm
FINISH: Available in: Anodize (Sulphuric) Dichromate Seal, Yellow-Green / Anodize (Sulphuric) Hot Water Seal, Clear / Anodize (Chromic) Hot Water Seal, Dark Gray / Anodize -Black / Cadmium Plate, Clear Chromate / Cadmium Plate, Commercial / Cadmium Plate, Gold Chromate / Nickel Plate / Chromium Plate (Bright) / Chromium Plate, Engineering / Chromium Plate Over Nickel Plate / Passivate / Iridite-Clear / Iridite-Gold #14 / Alodine 1200 / Black Oxide-Brass / Black Oxide- Stainless Steel / Zinc Plate .0002 Thick-Clear Chromate / Zinc Plate .0002 Thick, Yellow-Green Chromate
THREAD: M2 through M8 / External Thread- Class 6G / Thread Locking Products available.
Available with slotted heads upon request.
TOLERANCE: See chart on each part number page.
Diameter: Standard commercial bar stock tolerances.
THUMB NUTS: STANDARD SIZES
See Technical / Engineering Data
DIAMETER: 1/4" / 5/16" / 3/8" / 7/16" / 1/2" / 9/16" / 5/8" / 3/4"
SHAPE: Round, Hex
KNURL: Straight (for easy grip)
MATERIAL: Brass, Aluminum, Stainless Steel, Carbon Steel.
LENGTH: Wide variety of lengths in 1/4" up to 15/32"
FINISH: See above (Thumb Screws)
THREAD: 2 -56 through 3/8-16 / Internal Thread- Class UNC 2B.
TOLERANCE: See chart on each part number page.
Diameter: Standard commercial bar stock tolerances.
THUMB NUTS: METRIC SIZES
See Technical / Engineering Data
DIAMETER: 6mm / 8mm / 10mm / 13mm / 19mm
SHAPE: Round, Hex
KNURL: Straight (for easy grip)
MATERIAL: Brass, Aluminum, Stainless Steel, Carbon Steel
LENGTH: Wide variety of lengths in 6mm up to 12mm.
FINISH: See above (Thumb Screws)
THREAD: M2.5 through M8 / Internal Thread- Class UNC 6H.
TOLERANCE: See chart on each part number page.
Diameter: Standard commercial bar stock tolerances.
HANDLES & FERRULES:
STANDARD SIZES
See Technical / Engineering Data
DIAMETER: For Round: 1/8" through 1/2" / For Oval: 9/32" x 7/16" through 5/8" x 3/8" / For Rectangular: 3/16" x 1/2" through 1/4" x 1/2" / For Aluminum Extruded - Bar: 5/16" x 1/2".
SHAPE: Round, Oval, Rectangular, Half-Round
STYLE: Available in 24 different styles. Pull Handles, Offset Pull Handles, Pulls, Slanted Pull Handles, Folding Handles, Fixed Handles, Panel & Rack Handles, Standard Pulls, Offset Pulls, Slanted Pulls, Handle Ferrules, Internal Threaded Handles, External Threaded Handles, Free Fall Handles, All Position Handles, Two Position Handles, Three Position Handles, 90 Degree Handles, 180 Degree Handles.
MATERIAL: Brass, Aluminum, Stainless Steel and Carbon Steel upon request.
OVERALL HEIGHT: Wide variety of heights in 1/2" up to 4"
CENTER TO CENTER: Wide variety of lengths in 3/4" up to 12"
DECORATIVE FERRULE: Threaded and Unthreaded
FERRULE DIAMETER: 1/4" through 15/16"
FINISH: Available in: Anodize (Sulphuric) Dichromate Seal, Yellow-Green / Anodize (Sulphuric) Hot Water Seal, Clear / Anodize (Chromic) Hot Water Seal, Dark Gray / Anodize -Black / Anodize-Black High Lustre / Anodize-Black High-Satin Finish / Cadmium Plate, Clear Chromate / Cadmium Plate, Commercial / Cadmium Plate, Gold Chromate / Nickel Plate / Chromium Plate (Bright) / Chromium Plate, Engineering / Chromium Plate-Satin Finish / Chromium Plate Over Nickel Plate / Passivate / Bright Dip / Iridite-Clear / Iridite-Gold #14 / Alodine 1200 / Black Oxide-Brass / Black Oxide- Stainless Steel / Zinc Plate .0002 Thick-Clear Chromate / Zinc Plate .0002 Thick, Yellow-Green Chromate / Zinc Plate .0002 Thick, Black Chromate / Alkali Caustic Etch / Brushed Finish on metal / Handles without Plating are also available.
THREAD: 2-56 through 3/8-24 / Internal Thread- Class UNC 2B / External Thread- Class UNC 2A / Thread Locking Products available.
TOLERANCE: See Handles Chart: All Technical Data.
Diameter: Standard commercial bar stock tolerances.
HANDLES & FERRULES:
METRIC SIZES
See Technical / Engineering Data
DIAMETER: For Round: 3mm through 13mm / For Oval: 7mm x 11mm through 16mm x 9mm / For Rectangular: 5mm x 13mm through 7mm x 25mm / For Aluminum Extruded: 8mm x 13mm.
SHAPE: Round, Oval, Rectangular, Half-Round
STYLE: Available in 24 different styles. Pull Handles, Offset Pull Handles, Pulls, Slanted Pull Handles, Folding Handles, Fixed Handles, Panel & Rack Handles, Standard Pulls, Offset Pulls, Slanted Pulls, Handle Ferrules, Internal Threaded Handles, External Threaded Handles, Free Fall Handles, All Position Handles, Two Position Handles, Three Position Handles, 90 Degree Handles, 180 Degree Handles.
MATERIAL: Brass, Aluminum, Stainless Steel and Carbon Steel upon request.
OVERALL HEIGHT: Wide variety of heights in 13mm up to 102mm.
CENTER TO CENTER: Wide variety of lengths in 19mm up to 305mm.
DECORATIVE FERRULE: Threaded and Unthreaded
FERRULE DIAMETER: 6mm through 19mm
FINISH: Available in: Anodize (Sulphuric) Dichromate Seal, Yellow-Green / Anodize (Sulphuric) Hot Water Seal, Clear / Anodize (Chromic) Hot Water Seal, Dark Gray / Anodize -Black / Anodize-Black High Lustre / Anodize-Black High-Satin Finish / Cadmium Plate, Clear Chromate / Cadmium Plate, Commercial / Cadmium Plate, Gold Chromate / Nickel Plate / Chromium Plate (Bright) / Chromium Plate, Engineering / Chromium Plate-Satin Finish / Chromium Plate Over Nickel Plate / Passivate / Bright Dip / Iridite-Clear / Iridite-Gold #14 / Alodine 1200 / Black Oxide-Brass / Black Oxide- Stainless Steel / Zinc Plate .0002 Thick-Clear Chromate / Zinc Plate .0002 Thick, Yellow-Green Chromate / Zinc Plate .0002 Thick, Black Chromate / Alkali Caustic Etch / Brushed Finish on metal / Handles without Plating are also available.
THREAD: M2.5 through M10 / Internal Thread- Class 6H / External Thread- Class 6G / Thread Locking Products available.
TOLERANCE: See handles chart: All Technical Data.
Diameter: Standard commercial bar stock tolerances.
SHOULDER SCREWS:
STANDARD SIZES
See Technical / Engineering Data
DIAMETER: 1/4" / 5/16" / 3/8" / 7/16" / 1/2" / 9/16" / 5/8" / 3/4"
SHAPE: Round
HEAD: Slotted, Hex Socket Head (Broached), Torx®, Phillips
SLOT: Width- .047 through .094 / Depth- .062 through .109
BROACH / Hex Socket Head: 5/64" through 1/4" across the flats
TORX®:T10 through T55
PHILLIPS:#1 through #4
MATERIAL: Stocked in Type 303 Stainless Steel, 316 Stainless Steel, 416 Stainless Steel, 4140 Alloy Steel, Brass and Carbon Steel are available upon request.
LENGTH: Wide variety of lengths in 1/8" up to 1.500
FINISH: Standard Stainless Steel Shoulder Screws are not plated. Black Oxide or Passivate is available for Stainless Steel. For Brass and Carbon Steel the following are available: Cadmium Plate, Clear Chromate/ Cadmium Plate, Commercial/ Cadmium Plate, Gold Chromate/ Nickel Plate/ Chromium Plate (Bright)/ Chromium Plate, Engineering/ Chromium Plate Over Nickel Plate/ Black Oxide/ Zinc Plate .0002 Thick, Clear Chromate/ Zinc Plate .0002 Thick, Yellow/Green Chromate.
THREAD: 4-40 through 3/8-16 / External Thread- Class UNC 2A / Thread Locking Products available.
TOLERANCE: Head Thickness and Thread Length ± .005 / Shoulder Width + .000 - .001 / Length ± .005.
Diameter: Standard commercial bar stock tolerances.
SHOULDER SCREWS:
METRIC SIZES
See Technical / Engineering Data
DIAMETER: 6mm / 7mm / 8mm / 10mm / 11mm / 13mm / 16mm
SHAPE: Round
HEAD: Slotted or Hex Socket Head (Broached)
SLOT: Width: 1.2mm through 2.4mm / Depth: 1.6mm through 2.8mm
BROACH / Hex Socket Head: 2mm through 5mm across the flats
MATERIAL: Stocked in Type 303 Stainless Steel. Brass and Carbon Steel are available upon request.
LENGTH: Wide variety of lengths in 3mm up to 36mm
FINISH: Standard Stainless Steel Shoulder Screws are not plated. Black Oxide or Passivate is available for Stainless Steel. For Brass and Carbon Steel the following are available: Cadmium Plate, Clear Chromate/ Cadmium Plate, Commercial/ Cadmium Plate, Gold Chromate/ Nickel Plate/ Chromium Plate (Bright)/ Chromium Plate, Engineering/ Chromium Plate Over Nickel Plate/ Black Oxide/ Zinc Plate .0002 Thick, Clear Chromate/ Zinc Plate .0002 Thick, Yellow/ Green Chromate.
THREAD: M3 through M8 / External Thread- Class 6G / Thread Locking Products available.
TOLERANCE: Head Thickness and Thread Length ± .015 / Shoulder Width + .000 - .026 / Length ± .015.
Diameter: Standard commercial bar stock tolerances.
CABLE TIES: STANDARD SIZES
See Technical / Engineering Data
MATERIAL: Nylon 6/6, Nylon 6/6- UV Stabilized, Nylon 6/6- UV Stabilized / Heat Stabilized, Tefzel® and Halar®. One piece construction.
STYLE: Available in 5 different styles: Cable Ties, Identification Ties, Releasable Ties, Beaded Ties, Mounted Head Cable Ties.
LENGTH: 4" thru 48"
STRENGTH: 18 lbs. thru 250 lbs.
COLOR: Natural Nylon 6/6 is the standard. Also available in Black Nylon 6/6 and in different colors including fluorescents. Halar® Fluoropolymer cable ties have a distinctive maroon color, Tefzel® Fluoropolymer cable ties have a distinctive aqua blue color.
Cable Tie Combo-Packs: STANDARD
SIZES
See Technical / Engineering Data
MATERIAL: Nylon 6/6, Natural Nylon 6/6, Black Nylon 6/6. One piece construction.
COLOR: Fluorescent Nylon 6/6, Natural Nylon 6/6, Black Nylon 6/6.
Colors available.
Mounting Bases: STANDARD SIZES
See Technical / Engineering Data
MATERIAL: Natural Nylon 6/6 or Black Nylon 6/6
OPERATING RANGE: 18 lb. though 120 lb.
DIAMETER: 1/2" square through 2" square
COLOR: Natural Nylon 6/6 is the standard color. Available in Black Nylon 6/6. Unique design with Center Screw Hole which also allows for screw application along with adhesive application for added strength- if desired.
Tensioning Tools: STANDARD SIZES
See Technical / Engineering Data
MATERIAL: Plastic and Metal
OPERATING RANGE: 18 lb. though 175 lb.
Flexible Tubing: STANDARD SIZES
See Technical / Engineering Data
MATERIAL: Flexible Polyolefin Tubing
DIAMETER: 3/64" through 2"
COLOR: Colors available |
|
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
