Standard & Oddball Sizes
In- Between Lengths
In American Standard & Metric
291 Cleveland St • Orange NJ
1  800  526- 1389 • Fax  973 674- 3803

  UNICORP- Electronic Hardware Manufacturer


Standoffs, Spacers, Captive, Swage, Male-Female, Handles, Thumb Screws, Shoulder Screws, Insulating Washers, Jack Screws Male-Male Standoffs, Cable Ties, Plastic Circuit Board Supports & Electronic Hardware.

   Home  Search  Quote  Cross  Order Online  Catalog  Reps  Technical  Terms  Distributors  About Us  Contact Us

 

Unicorp Product Overview- Metric Sizes
UNICORP is a worldwide leader in manufacturing stock & custom electronic hardware, handles
 & precision fasteners used by leading companies in nearly every industry since 1971.

RoHS Compliance Statement     DFARS Statement    WEEE Statement
 

Metric Standoffs- Threaded

PART NUMBER:  (MP101 thru MP3353)

DIAMETER:  3mm / 4mm / 4.5mm / 5mm / 6mm  / 8mm / 10mm / 13mm / 16mm / 19mm

SHAPE:  Round, Square, Hex

MATERIAL:  Brass, Aluminum, Stainless Steel, Carbon Steel, Nylon, Teflon®, Linen Base Phenolic, 10%
                     Glass-Filled Lexan®,  Delrin®, Ultem®
LENGTH:  Wide variety of lengths in .5mm (.019) increments- up to 254mm
FINISH:  Available in 28 finishes-  See Chart

THREAD:  M1.6 through M14 /  Internal- Class 6H.  Thread Locking Products available.

TOLERANCE:  Length: Up to 100mm  ±  .13mm /  From 101mm to 150mm ± 20mm / Over 150mm ±  .25mm

                Diameter: Standard commercial bar stock tolerances.

 

Metric Spacers- Unthreaded Standoffs

PART NUMBER: (MS101 thru MS3101)
DIAMETER:   3mm / 4mm / 4.5mm / 5mm / 6mm / 8mm / 10mm / 13mm / 16mm / 19mm
SHAPE:  Round, Square, Hex
MATERIAL:  Brass, Aluminum, Stainless Steel, Carbon Steel, Nylon, Teflon®, Linen Base Phenolic, 10%
                      Glass- Filled Lexan®, Delrin®, Ultem®
LENGTH:  Wide variety of lengths in .5mm (.019) increments- up to  51mm
FINISH:  Available in 28 finishes-   See Chart
INSIDE HOLE DIAMETER:  Ranging from 1.7mm  through 15.5mm  ±  .13mm for screw sizes M1.6 through M14. 
TOLERANCE:  Length: Up to 51mm  ±  .13mm /  Inside Hole Diameter:  ±  .13mm
                Diameter: Standard commercial bar stock tolerances.

 

Metric Swage Standoffs & Swage Spacers
Threaded, Unthreaded / Clear Hole
& Rivet Type
Swaging Tools (Punch & Anvil)

   

PART NUMBER: (MSS100 thru MSS1071- Threaded) (MSU100 thru MSU720- Unthreaded)
                               (UP1 thru UP5 Punch) (AN640 thru AN1110 Anvil)
DIAMETER:  3mm / 4mm / 4.5mm / 5mm / 6mm / 8mm / 10mm
SHAPE:  Round, Hex
MATERIAL:  Brass, Aluminum, Stainless Steel, Carbon Steel   
BODY LENGTH:  Wide variety of lengths in .5mm increments- up to 51mm
SHANK LENGTH:  Wide variety of lengths ranging from 1.9 through 7.4
FINISH:  Available in 28 finishes- See Chart
THREAD:  M1.6 / M2.5 / M3 / M3.5 / M4 / M5 / Internal Thread- Class 6H
INSIDE HOLE DIAMETER:  Ranging from 1.8  through 5.3 for screw sizes M1.6 through M5
TOLERANCE:  Body Length:  ±  .13 /  Shank Length:  ±  .08 /  Inside Hole Diameter:  +.00 - .08
               Diameter: Standard commercial bar stock tolerances.

 

Metric Male-Female Standoffs
Internal & External Threads

PART NUMBER: (MMF1101 thru MMF2961)
DIAMETER:   3mm / 4mm / 4.5mm / 5mm / 6mm / 8mm / 10mm / 13mm
SHAPE:  Round, Square, Hex
MATERIAL:  Brass, Aluminum, Stainless Steel, Carbon Steel, Nylon, Delrin®
LENGTH:  Wide variety of lengths in .5mm increments- up to 200mm
FINISH:  Available in 26 finishes- See Chart
THREAD:  M1.6 through M10 / Thread Locking Products available.  Internal Thread- Class 6H / External
      Thread- Class 6G.  Internal thread depth adjusted where body dimensions will not permit full thread depth.
TOLERANCE: Length: Up to 100mm ± .15mm / From 101mm to 150mm  ± .20mm / Over 150mm ±  .25mm
                No Undercut on Nylon or Delrin®
                Diameter: Standard commercial bar stock tolerances.

 

Metric Hex Jack Screws Standoffs
Internal & External Threads

PART NUMBER: (MJAX101 thru MJAX210)
DIAMETER:  4.5mm & 5mm
SHAPE:  Hex
MATERIAL:  Brass, Aluminum, Stainless Steel, Carbon Steel
BODY LENGTH:  5mm
EXTERNAL THREAD LENGTH:  Ranging from 5mm through 19mm. Thread Locking Products available.
FINISH:  Available in 26 finishes- See Chart
THREAD:  M3 x 0.5 Internal Thread- Class 6H /  M3 x 0.5 External Thread- Class 6G. Thread Locking
                   Products available.
TOLERANCE: Body Length:  ± .15mm / External Thread Length  ±  .25mm    
               Diameter: Standard Commercial Bar Stock Tolerances. All Jackscrews are shipped unassembled
               with  2- M3 flat washers, 1- M3 lock washer and 1- M.3 x 0.5 nut.

 

Metric Male-Male Standoffs
External Threads

PART NUMBER: (MMX1101 thru MMX1898)
DIAMETER:  3mm / 4mm / 4.5mm / 5mm / 6mm / 8mm / 10mm / 13mm
SHAPE:  Round, Square, Hex
MATERIAL:  Brass, Aluminum, Stainless Steel, Carbon Steel, Nylon, Delrin®
BODY LENGTH:  Wide variety of lengths- .5mm increments- up to 100mm
EXTERNAL THREAD LENGTH:  Ranging from 3mm through 13mm depending on the thread size.
         Thread Locking Products available.
FINISH:  Available in 26 finishes- See Chart
THREAD: M2 through M8 /  External- Class 6G / Thread Locking Products available.  Mix and Match Different Threads and Lengths For Each Part.
TOLERANCE for Brass, Aluminum, Stainless Steel and Carbon Steel:  Body Length: Up to 100mm  ±  .15mm/
        Over 100mm  to 150mm  ±  .20mm / Over 150mm  ±  .25mm /  External Thread Length Tolerance is  ±  .15mm
TOLERANCE for Nylon and Delrin®:  Body Length: For all lengths the Tolerance is  ±  .25mm / External Thread
        Length Tolerance is  ±  .20mm
        Diameter: Standard commercial bar stock tolerances. No Undercut on Nylon or Delrin®.

 

Metric Captive Panel Hardware
Screws, Retainers, Retaining Washers,
Springs & Decorative Panel Washers

 

PART NUMBER: (M4001 thru M4528) (M40R01 thru M46R24) (MRN1 thru MRN7) (MRS1 thru MRS7)
                              (MSP1 and MSP2) (MPW431 thru MPW436)
DIAMETER: 5mm through 19mm
SHAPE:  Round, Hex.  Hex head cannot be knurled. Hex head only available for M4000 and M4100 series.
MATERIAL:   Stainless Steel, Carbon Steel, Aluminum, Brass (Also in Nylon For Retainer Washers Only)
KNURL:  Straight
HEAD:  Knurled and Slotted
CONFIGURATION:  Round Head Screws: Knurled / Slotted- Knurled /Unslotted.
             Hex Head Screws: Slotted & Unslotted.
LENGTH:  Wide variety of lengths in .5mm increments- up to 51mm
LENGTH (for retainers) :  Wide variety of lengths in 6.5mm through 16mm
RETAINER:  Standard and Spring Loaded, 1.3mm through 16mm shank length
FINISH:  Available in 24 finishes-  See Chart
THREAD:  M2.5 through M8 /  Internal Thread- Class 6H / External Thread- Class 6G / 
              Thread Locking Products available.
TOLERANCE: See chart on each part number page.
              Diameter: Standard commercial bar stock tolerances.

 

Metric Insulating Washers
Non- Metallic, Shoulder & Flat

PART NUMBER:  (MWS1001 thru MWS1636) (MWF3001 thru MWF3595)
DIAMETER:  3mm through 25mm
SHAPE:  Round
MATERIAL:  Nylon, Teflon ®, Glass-Filled Lexan®, Ultem®, Delrin®, Phenolic- Linen Based
                     (We do not use Paper- Based Phenolic, which is less expensive but may crack).
LENGTH:  For Head Thickness: wide variety of lengths in 0.4mm through 1.6mm
FLAT WASHER THICKNESS:  0.4mm through 2.4mm
INSIDE HOLE DIAMETER:  Ranging from 0.74 through .413 for screw sizes M1.6 through M10. 
                   Reamed to + .16 / - 0.0, conforming to screw tolerances.
SHANK LENGTH:  Wide variety of lengths 1mm through 13mm
SHANK DIAMETER:  Machined to  +  0.0 / - 0.16 assuring precision fit to mating hole.
EDGE:   Chamfered to permit smooth entry.
FINISH:  Colored material available upon request 
TOLERANCE:   Inside hole diameter  + 0.17 / - 0.00 - All other tolerances see All Technical Chart
               Diameter: Standard commercial bar stock tolerances. Shoulder Washers, Flat Washers-
               Precision Machined, Not Molded.

 

Metric Thumb Screws
Knurl, Shoulder, Plain, Push

 

PART NUMBER:  (MTHS1001 thru MTHS4084)
DIAMETER:  4mm / 4.5mm / 5mm / 6mm / 6.5mm / 8mm / 10mm / 11mm / 13mm
SHAPE:  Round
KNURL:  Diamond(for easy grip)
MATERIAL:  Brass, Aluminum, Stainless Steel, Carbon Steel
LENGTH:  Wide variety of lengths in 8mm up to 58mm
FINISH:  Available in 20 finishes- See Chart
THREAD:  M2 through M8 / External Thread- Class 6G /  Thread Locking Products available. 
               Available with slotted heads upon request
TOLERANCE:  See chart on each part number page
               Diameter: Standard commercial bar stock tolerances.

 

Metric Thumb Nuts
Round with Knurl / Hex with No Knurl

    

PART NUMBER:  (MTHN5001 thru MTHN5007 / MTHN5008 thru MTHN5014)
DIAMETER:  6mm / 8mm / 10mm / 13mm / 19mm
SHAPE:  Round, Hex
KNURL:  Straight (for easy grip)
MATERIAL:  Brass, Aluminum, Stainless Steel, Carbon Steel
LENGTH:  Wide variety of lengths in 6mm up to 12mm
FINISH:  Available in 20 finishes- See Chart
THREAD:  M2.5 through M8 / Internal Thread- Class UNC 6H
TOLERANCE:  See chart on each part number page. Diameter: Standard commercial bar stock tolerances.

 

Metric Handles & Ferrules
Pull, Offset Pull, Slanted Pull, Pulls, Folding, Bar, Fixed, Panel & Rack, Standard Pull,
Internal Threaded, External Threaded,
Free Fall, All Position, Two Position, Three Position,
90 Degree, 180 Degree, Ferrules.  

   

PART NUMBER:  (MA1002 thru MX1288) (MED101 thru MEF160) (M10-101 thru M14-127)
DIAMETER:  For Round: 3mm through 13mm / For Oval: 7mm x 11mm through 16mm x 9mm /
               For Rectangular: 5mm x 13mm through 7mm x 25mm /  For Aluminum Extruded - Bar: 8mm x 13mm
SHAPE:  Round, Oval, Rectangular, Half-Round
STYLE:  Available in 24 different styles. Pull Handles, Offset Pull Handles, Pulls, Slanted Pull Handles,
               Folding Handles, Fixed Handles, Panel & Rack Handles, Standard Pulls, Offset Pulls, Slanted Pulls,
               Handle Ferrules, Internal Thread Handles, External Thread Handles, Free Fall Handles,
               All Position Handles, Two Position Handles, Three Position Handles,
               90 Degree Handles, 180 Degree Handles.
MATERIAL:  Brass, Aluminum, Stainless Steel and Carbon Steel upon request.
OVERALL HEIGHT:  Wide variety of heights in 13mm up to 102mm
CENTER TO CENTER:  Wide variety of lengths in 19mm up to 305mm
DECORATIVE FERRULE:  Threaded and Unthreaded
FERRULE DIAMETER:  6mm through 19mm
FINISH:  Available in 28 finishes- See Chart.  Handles without Plating also available.
THREAD:  M2.5 through M10 /  Internal Thread- Class 6H / External Thread- Class 6G / 
               Thread Locking Products available.
TOLERANCE:  See handles chart:  All Technical Data
               Diameter: Standard commercial bar stock tolerances.

 

Metric Precision Shoulder Screws
Slotted & Hex Socket Head (Broached)

PART NUMBER:  (MSCS236-1 thru MSCS629-20) (MSCB236-1 thru MSCB629-20)
DIAMETER:  6mm /  7mm /  8mm /  10mm /  11mm /  13mm / 16mm
SHAPE:  Round
HEAD:  Slotted or Hex Socket Head (Broached)
SLOT:  Width: 1.2mm through 2.4mm  / Depth: 1.6mm through 2.8mm
BROACH / Hex Socket Head:  2mm through 5mm across the flats
MATERIAL:  Stocked in Type 303 non- magnetic Stainless Steel. 
             Brass and Carbon Steel are available upon request.
LENGTH:  Wide variety of lengths in 3mm up to 36mm
FINISH:  Standard Stainless Steel Shoulder Screws are not plated. Black Oxide or Passivate for
             Stainless Steel is available.  Also available in 13 finishes for Brass and Carbon Steel- See Chart
THREAD:  M3 through M8 /  External Thread- Class 6G /  Thread Locking Products available.
TOLERANCE:  Head Thickness and Thread Length  ± .015 / Shoulder Width  + .000 - .026 /  Length  ±  .015
             Diameter: Standard commercial bar stock tolerances.

 ORDER ONLINE     800 526-1389  


  291 Cleveland Street, Orange, New Jersey  07050  USA
Toll Free: 1.800.526.1389      Phone: 973.674.1700       Fax: 973.674.3803
Feedback   Legal Notice   Copyright   Services   Jobs   Contact Us  Email Us
Copyright©2006  UNICORP Inc., All rights reserved.  Privacy Statement